Tuesday, September 26, 2023

Ignitor For Whirlpool Gas Oven

Must read

Spark Ignition Switch Wire Harness

Whirlpool Gas Oven Igniter Replacement #98005652

If your Whirlpool stove top igniter still doesnt work after replacing it, the next thing you should check is the spark switch wire harness. Below, we have listed the steps you need to follow in order to replace your Whirlpool stove top switch wire harness

Step 1: Pull the oven away from the wall.

Step 2: Unplug the ovens power cord from the outlet.

Step 3: Shut of the ovens gas supply.

Step 4: Lift off the burner grates.

Step 5: Also lift off the caps from all the burners except the center one.

Step 6: Lift the center burner base assembly off.

Step 7: Using a Philips head screwdriver, take out the screws which hold the burner bases to the stove top.

Step 8: Lift each burner base up and disconnect the wire from the igniter. Make sure the wire doesnt fall through.

Step 9: Take out the Philips head screws which secure all the orifice holders to the stove top.

Step 10: Open the door of the oven.

Step 11: Pull off the control knobs of the oven making sure to note where each one goes first.

Step 12: Use the Philips head screwdriver to take out the screws underneath the ovens front panel which secure it.

Step 13: Lift the front panel off and set it aside.

Step 14: Take out the Philips head screws which hold the stove top in place. There should be two underneath the stove top.

Step 15: Lift the stove top.

Step 16: Take out the screw which holds the spark module bracket to the right side of the stove top.

Step 17: Set the stove top aside.

Step 19: Set the panels aside.

Whirlpool Oven Igniter Clicking How To Fix

If your Whirlpool oven igniter keeps clicking, some water probably got into it. To stop the igniter from clicking, you will need to dry it. Follow the steps below to dry your Whirlpool oven igniter

Step 1: Unplug the ovens power cord.

Step 2: Shut off the ovens gas supply.

Step 3: Take out the screws which hold the ovens rear access cover in place using a Philips head screwdriver. The cover is on the lower right of the ovens rear.

Step 4: Disconnect the white wire plug from the oven igniter and open the door.

Step 5: Remove the oven racks and lift out the ovens bottom panel.

Step 6: Use a 5/16th inch socket or nut driver to take out the screws which hold the igniter to the right side of the burner tube.

Step 7: Remove the igniter.

Step 8: Clean the igniter with a paper towel to get rid of any moisture.

Step 9: Leave the igniter out overnight to dry.

Step 10: Once the igniter is completely dry, take it back to the oven and secure it to the burner tube with the screws.

Step 11: Reposition the ovens bottom panel.

Step 12: Slide the racks back into the oven.

Step 13: Shut the oven door.

Step 14: Go back to the ovens rear and reconnect the white wire plug to the igniter.

Step 15: Reposition the lower access cover and hold it in place with the screws.

Step 16: Plug the ovens power cord back into the outlet.

Step 17: Turn the ovens gas supply back on.

Step 18: Return the oven to its usual position.

Check out these articles

Replacing A Faulty Igniter

If your igniter is no longer working in your oven or is far too dirty to realistically clean off well enough, then it needs to be replaced. Before beginning, you will want to disconnect your oven from its power source as well as to shut off the gas to it. If you havent already, remove the oven racks and unthread the screws to the base plate so it can be removed.

The most crucial thing to remember before removing the old igniter is the position that it is in. You want to install the new igniter in that same position. You will want to begin by removing the mounts on the igniter and pulling upwards to reveal two wires. These need to be removed. Some igniters may be secured using wire nuts that will also need to be removed.

When installing the new igniter, you want to handle it very carefully. One accidental drop could render it completely useless as it is a rather fragile piece. Start by remounting the igniter before connecting the wires. This will ensure proper positioning without having to worry about where the wires sit. If your igniter uses a wire nut and you are not reusing the previous ones, makes sure you use a metal nut rather than a plastic one. The ambient heat of your oven will melt the plastic.

For many, repairing any gas appliance is a concern. While replacing igniters stays away from the gas line, you may be more comfortable leaving this up to the professionals.

Also Check: How To Clean Burnt Oven

Ways To Fix Whirlpool Accubake Gas Oven Range Not Lighting

If you own a Whirlpool oven, you are probably enjoying the amazing features and love the functions available. However, any oven can go through functionality issues with time, and Whirlpool accubake gas range oven, not lighting is one of the complaints by users. In case you are having the same issue, we are sharing the solutions with you!

Solving Igniter Problems In Your Gas Oven

7432P143

If you own a gas oven, then, for the most part, you own a pretty reliable appliance. However, a gas oven is not immortal. Over time, every appliance suffers from wear with regular use, and parts will go out. However, one of the most worrisome parts to go faulty is the igniter in your oven. Not only will a faulty igniter mean your oven will not produce any flame or heat, but it could mean that it continues to release natural gas as it tries to ignite. That is something that no one wants. If you believe your oven is having igniter problems, here is how to diagnose them and repair them.

Recommended Reading: Dutch Oven With Glass Lid

Cleaning A Gas Igniter

In most gas ovens, the igniters are hidden away under a bottom covering. This protects from direct exposure to food from boiling over the pan, for example. However, grease and food particles can still reach it through the ambient air. Over time, this can affect the igniters function, but unfortunately, most oven ignitors use hot-surface ignition which makes it tough to clean without damaging or breaking the ignitor. Most cases, its best to just replace the igniter.

Diagnosing Problems Through Noise

Most often, appliance owners are able to diagnose igniter problems through noise alone. By listening to your gas oven, you can actually tell if igniter problems are coming. Obviously, the most concrete sign is when your oven isnt producing heat. As there is no electric element in a gas oven, when the igniter doesnt work, the oven can produce no heat. Though often, signs of the igniter going outcome before this happens.

One noise you want to look out for is a loud boom noise. You can expect to hear gas hissing and then a whoosh as it ignites, but if you hear a relatively loud boom, as in one you can hear in another room, then that is cause for concern. What is actually happening is that the igniter is not working properly, but is still working. The gas is released and built up until when it finally does ignite, it causes a small explosion. This signals slow ignition that most likely comes from dirty igniters. This needs to be addressed as soon as possible because obviously, it is potentially dangerous and hard on your gas oven as well.

You May Like: How To Cook Tilapia Oven

Spark Ignition Switch And Harness Problems

Theres a small chance that one of your stovetop burners spark ignition switches could be defective. It acts as a go-between sending a flow of power to the ignition module once the electric current is activated.

If its current contacts become wet, or something is preventing them from closing, the whole thing will continue operating in the default position no matter the adjustments made on your dial.

Each switch can be tested individually to see if it still functions on its own and when faulty, it should be replaced by another.

How To Test A Whirlpool Oven Igniter

Whirlpool Gas Range Surface Igniter Replacement #W10515459

Testing a Whirlpool oven igniter with a multimeter is a great way to determine if its faulty so that you dont waste money buying a new one when you dont need to. Below, we have listed the steps you need to follow in order to test a Whirlpool oven igniter

Step 1: First, take the igniter out of the oven. If you dont know how to access your Whirlpool oven igniter, read the section directly above this one.

Step 2: Get a multimeter.

Step 3: If you are using an analog multimeter, turn the dial to the lowest ohms setting. Next, touch the multimeter probes together then adjust the needle on the display to read 0. For a digital multimeter, simply turn the dial to the lowest ohms setting.

Step 4: Touch the multimeter probes to the small metal pins in the igniters wire connector.

Step 5: Look at the multimeter display. If you see a reading anywhere from 0 to 1,100 ohms, the igniter is still good. If the display doesnt change at all, there is no continuity. Get a new Whirlpool oven igniter if there is no continuity.

The video below will give you a visual of how to test a Whirlpool oven igniter.

Prices pulled from the Amazon Product Advertising API on:

Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on at the time of purchase will apply to the purchase of this product.

Recommended Reading: Cedar Plank In Oven Salmon

More articles

Latest article