Friday, March 1, 2024

Whirlpool Gas Oven Not Heating

Must read

There Is No Gas Supply

Whirlpool – Range / Oven – Not heating – Diagnostic & Repair – Bake Element

Even if your gas oven receives enough electricity to power the igniter and other components, your oven wont heat if theres no gas coming into the unit. Gas ovens need a consistent gas supply to start heating and power the oven cycles throughout the cooking time.

There are two possible causes a gas oven isnt receiving enough gas:

  • The gas valve is turned off.
  • The home gas line isnt receiving gas.

Whirlpool Oven Not Heating To Temperature

One of the most important things when it comes to cooking with an oven is being able to heat your oven to the correct temperature. This is something that can make or break the baking of a cake, the long and slow process of cooking a roast, or the quick broil of a dish that needs a bit of crunch. If you have been using your Whirlpool oven but notice that it is indicating that it is not heating to temperature, what could be the cause?

If you notice that your Whirlpool oven is not heating to the correct temperature, it could be that this piece is too close to the oven wall, which will cause the temperature to read improperly. Simply pull the sensor gently away from the wall of the oven and see if the temperature reads accurately.

The Safety Valve Is Malfunctioning

A gas oven safety valve works with the igniter and the burner tubes. When the igniter heats up to the required level, the bimetallic strip in the oven safety valve opens the valve to send gas to the burner tubes. The burners then turn on to heat the oven.

A malfunctioning safety valve isnt a common gas oven issue. However, the bimetallic strip within the safety valve can sometimes be faulty and fail to open, causing the gas not to go into the burner tube and the oven not to start heating.

You can test the valve for continuity and replace it if its malfunctioning.

Don’t Miss: Wall Oven Electric 24 Inch

The Thermostat Is Defective

Your gas ovens thermostat controls and monitors the oven temperature. When the set temperature is reached, the thermostat signals the igniter to stop heating. Once the temperature drops below the set value, the thermostat sends a signal to start heating.

If the thermostat is bad, it wont communicate with the igniter, which means your oven cannot initiate the heating process. You should replace a faulty thermostat.

Oven Not Getting Enough Power

Whirlpool Gas Convection Oven Fan Not Working

One possible reason why your Whirlpool oven wont heat up is that its not getting enough power. This could be due to a problem with the electrical outlet, the circuit breaker, or the oven itself. If you think this might be the problem, check to make sure that the oven is securely plugged in and that the circuit breaker hasnt been tripped.

Also Check: How To Make Hard Boil Eggs In The Oven

Make Sure The Igniter Is Working

The next step is to check the igniter to ensure it is working correctly. The igniter lights the gas when you turn your oven on and when it stops working, your oven will be unable to heat.

This is how to check the igniter:

  • Locate the igniter .
  • Attempt to turn your oven on.
  • If the gas doesnt ignite, test the igniter with a multimeter .
  • If the igniter doesnt have continuity, replace it. If it does have continuity, reattach it to your oven and move on to step 4.
  • Once the new igniter is installed into your Whirlpool oven, attempt to turn your oven on. If it still doesnt heat, move on to step 4.
  • Oven Gas Supply Not Connected

    Gas ovens not only require gas to turn on but also to supply a steady flow of heat to cook food. If your gas-powered Whirlpool oven doesnt heat up test the gas supply by turning on a range burner. If the burner functions normally, the gas supply is adequate.

    If the burner doesnt light, move your oven away from the wall to make sure that the gas cutoff valve is still open. If it is, contact your local gas supplier to safely assess the problem.

    Don’t Miss: Steaks In The Oven Recipe

    Whirlpool Oven Control Panel Not Working

    Whirlpool ovens come with a control panel that includes several important buttons and options that can allow us to cook with ease and convenience.

    However, if even one of those buttons stops working, its almost impossible to use the oven.

    After all, there is no way to set the temperature or start cooking without the use of the control panel.

    Possible solution:

    To fix your control panel, start by checking the connections of wires to the control panel.

    However, make sure to turn off the oven before doing so as a safety measure.

    If you dont notice any faults with the wiring, check the printed circuit board for faults and clean it.

    Oven Not Getting Power

    Whirlpool Oven Won’t Heat – How to Range Troubleshoot a Whirlpool Oven Not Working

    A Whirlpool oven not heating up can sometimes be more of a power concern than an appliance malfunction. Heres how to determine if your oven isnt getting the power it needs:

    • Make sure the oven is properly plugged into its outlet.
    • Use a multimeter to test the outlets function. An electric oven requires 240V of electricity while a gas model needs 120V.
    • For electric ovens, check your homes fuse or circuit breaker box. Replace any blown fuses or reposition tripped breakers.

    You May Like: Best Outdoor Gas Pizza Oven

    Whirlpool Gas Oven Will Not Ignite

    When using a Whirlpool gas oven, owners are able to bake evenly at high and low temperatures, by simply turning on their ovens and allowing them to preheat. This all happens through a small ignition which then produces the flame that heats the entire oven. However, if you own a Whirlpool gas oven but notice that it will not ignite, you are left wondering what could be the cause of the issue and what you can do to get this appliance to ignite once again.

    If your Whirlpool gas oven will not ignite, it could be that the bake igniter or the bake burner tube within the oven simply need to be cleaned off and wiped down. To do this, simply take a rag with a proper cleaning solution and wipe down both items well to see if ignition comes back.

    If you wipe down both of these items yet are still not able to ignite your Whirlpool gas oven, it could be that the valve which transports gas to your oven is the problem. If you have experience, you can troubleshoot this particular issue, but when it comes to dealing with gas, typically the best option is to hire a professional to ensure that all processes are followed as safely as possible.

    Problem: It’s Not Heating To The Correct Temperature

    If you notice food taking longer to cook than it should or coming out of the oven undercooked, your oven might not be reaching the desired temperature. There are a few different reasons this might happen.

    Cause: If the temperature sensor inside the oven is not working as intended, it can cause the oven to not heat to the correct temperature. This can be caused by a faulty temperature sensor or a temperature sensor that is touching the wall of the oven.

    Fix: Make sure the temperature sensor is not touching the inside wall, as this will affect its ability to accurately measure the internal temperature of the oven. If it is, reposition it so that it’s not making contact with the wall. If it’s still not heating correctly, you can use an ohmmeter to test that the sensor is working. The resistance of the sensor should rise with the internal temperature of the oven. Like with a heating element or gas igniter, replacing the temperature sensor is a quick and easy fix you can do yourself.

    Cause: If it’s still not heating to the correct temperature and you’ve checked or replaced the heating elements, gas igniter and temperature sensor, it may simply need to be calibrated.

    You May Like: 36 Inch Double Oven Gas Range

    How To Test And Replace A Defective Gas Oven Thermostat

    Follow these steps to test and replace a gas oven thermostat:

  • Cut power to the oven by flipping the circuit breaker switch and making a quarter turn to the gas supply valve handle. As I said earlier, the handle for the latter should be perpendicular to the gas line if its turned off.
  • Remove the screws holding the ovens rear panel using a Phillips head screwdriver and set the cover aside.
  • Locate the oven thermostat at the bottom right of the oven rear. Disconnect the wire that leads to the plastic plug by pulling both ends of the plug.
  • Unthread the two screws holding the thermostat to the oven and carefully pull out the thermostat. Set it aside for testing.
  • Set the multimeter to the lowest ohms reading. Place each multimeter probe on a terminal of the thermostat. The multimeter should show a reading between 1,000 and 1,100 ohms if it has continuity. If the reading is far from this, the thermostat is defective and must be replaced.
  • Take the new thermostat and slide it through the hole into the oven. Fasten the securing screws.
  • Hold the two ends of the plastic plug and reattach it to the thermostat.
  • Put the rear panel back and thread the screws to secure it.
  • Power the oven by turning on gas and electricity and test the oven to see if heating resumes.
  • This Repair Clinic video on YouTube talks about the Whirlpool gas oven and will give you a better idea of how to perform the above steps:

    Fix Appliances Ca Your Trusted Authorized Appliance Repair Service

    Whirlpool WFG515S0ED

    Fix Appliances CA services all residential and light commercial gas appliances, not only the kitchen but laundries, such as ranges, ovens, cooktops and dryers. Experts of our company are prepared and experienced in working with electric ovens and gas ones as well. Their work includes the installation, maintenance and repair of major brands. Moreover, Fix Appliances CA is an authorized company for most gas appliance makers.

    Red Tag from Enbridge or Uniongas. A red tag on a gas range or a gas dryer typically means that the equipment is not safe to operate and a technician has to put a red tag on it, which means the gas will be shut off until the problem is fixed. No worries, our team has you covered.

    No matter what the problem with your gas and propane appliance is, even when we talk about gas ovens, we solve any troubleshoot issues with them on a same-day basis. You are welcome to give us a call at or submit a request online. Our highly trained and qualified gas experts will do their best.

    PROFESSIONAL APPLIANCE SERVICE

    Also Check: Best Outdoor Pizza Oven For Home

    My Gas Oven Wont Turn On But The Stove Works

    If your gas oven wont turn on but the stove still works, youre in the right place.

    Thankfully, most of the time this problem is caused by either a problem with your power, the gas, the gas igniter, the burners, or in rare cases the temperature control thermostat.

    In this article, we will give you step-by-step instructions for how to find the cause of the problem and fix it so that you can get back to using your oven again.

    Lets get into it.

    Whirlpool Oven Baking Unevenly

    At times, you will notice your oven-cooked food to be unevenly baked.

    This is a common problem with Whirlpool ovens that are often disguised as cooking mistakes.

    Ovens baking unevenly are typically caused by the bake element being burnt out, only the broil element will heat the oven. As a result, the oven will heat unevenly. When the bake element is properly heated, it glows red hot.

    Following the solutions mentioned below will allow you to cook food evenly again.

    Possible solution:

    • Look for holes or blisters to determine whether the baking element has burned out as it will be obviously damaged. Using a multimeter, check the bake element for continuity to see whether it has burned out. Replace the baking element if it lacks continuity.
    • Debris can often get stuck between the blades of convection fans and stop it from circulating hot air around the oven for an even temperature. So, you may be able to solve this problem by removing debris.
    • However, removing debris doesnt help test the fan motor for continuity using a multimeter. If there is no current passing, replace the motor and fix the connection to it.

    Recommended Reading: Gas Oven Won T Light

    Can You Bypass A Gas Oven Igniter

    The ignitor lights the pilot light when the stoves controls are engaged. This saves gas because the pilot light is not burning all time as it did in older models. However, you may wish to bypass the electronic ignitor. You can bypass the ignitor in your gas stove by following a straightforward procedure.

    The Interior Of Electric Ovens Has Heating Elements At The Top And Bottom To Generate Heat For Cooking When Working Correctly The Heating Elements Generate A Steady Even Heat And Uniform Red Glow A Whirlpool Oven Not Working Properly May Have A Burned

    Oven Repair – Not Heating Correctly – Long Bake Times -Whirlpool , Maytag & KitchenAid

    Additional signs of a burned-out heating element include:

    • Dark spots or blistering
    • Lack of continuity with multimeter testing

    A burned-out heating element can result from the high temperatures of an ovens self-cleaning function. This is why most oven maintenance tips recommend using a natural oven cleaner instead of the self-clean feature. Since it cant be repaired, a burned-out heating element should be professionally replaced.

    Read Also: 6 In 1 Air Fryer Oven

    How To Assess And Fix A Faulty Gas Oven Igniter

    You can check if your gas oven igniter is heating by checking if the element glows after turning on the oven and if the burner turns on 3 minutes after the oven is turned on.

    If the igniter doesnt glow and the burner doesnt turn on within 90 seconds, the igniter isnt heating enough to signal the safety valve to open the gas. This is a sign that the igniter is faulty and needs replacement. You can also test the igniter for continuity.

    Here are the steps for testing and replacing a faulty gas oven igniter:

  • Turn off electricity to the oven via the circuit breaker.
  • Cut the gas supply via the gas supply valve.
  • Open the door and take out the oven racks.
  • Lift the bottom panel and take it out of the oven. You may need to unthread some screws to remove the bottom panel in some oven models.
  • Check the overlapping of the igniters carbide electrode on the burner holes before taking anything out.
  • Loosen the screws holding the igniter bracket to the burner.
  • Disconnect the igniters wire harness and remove the igniter plug from the harness by pressing the securing tabs.
  • Take out the igniter from the oven.
  • Test the igniter for continuity to confirm if its the one causing the issue. To do this, rotate the multimeter dial to the lowest reading for ohms of resistance. Touch each terminal of the igniter with a probe of the multimeter.
  • In that case, you can replace the igniter as follows.

  • Rework the overlapping of the electrode carbide to the burner holes.
  • Whirlpool Oven Not Working

    No matter what brand of oven you own, the most basic expectation is that you should be able to turn it on, preheat it, and get to baking or cooking what you need without having to think twice about the process. Even more so, if you own a quality Whirlpool oven, this process should be even more cut and dry, leaving some owners rather confounded when they find that their appliance is not working as it should. If this is the case for you, continue reading.

    If your Whirlpool oven is not working, one of the first things you need to check is the electrical supply for your appliance. Pull your oven from its position and confirm that it is plugged in properly, then check to make sure that the outlet itself is working by plugging in another device.

    If you have an electric Whirlpool oven, it should be plugged into a 240V receptacle to work as it should and if you have a gas Whirlpool oven, it should be plugged into a 120V receptacle. If your outlet cannot support this voltage, this could be where your problem lies. If you plug another device into the outlet and there is still no power, be sure to check that a breaker hasnt accidentally been turned off, cutting off power to your oven and causing it to stop working.

    You May Like: Maytag Double Oven Electric Range

    Convection Fan Not Working Properly

    Is your convection model Whirlpool oven not cooking evenly? The convection fan may have malfunctioned. This fan circulates the ovens heated air, creating faster cook times and more evenly-cooked food. If the fan isnt working properly, meals may take longer to cook or will not cook as evenly as they normally do.

    A failed convection motor or broken or blocked fan blade can all result in the fan not working properly. Many blade obstructions can be removed to restore function. However, the fan must be replaced if a blade is broken or multimeter testing shows it has no continuity.

    Your local oven repair service can fix a Whirlpool oven not cooking evenly or address any other malfunction. Call or schedule your repair online with Aviv Service Today!

    Faulty Whirlpool Oven Igniter

    Shop Whirlpool 5

    If your gas connection is intact then a faulty igniter may be another reason for a gas-fueled Whirlpool oven not heating. The igniter has two essential functions in starting the oven. First, it must channel enough electricity to open the oven safety valve and allow gas to flow. Second, it must get hot enough to ignite the gas as it flows into the burner.

    To assess the igniter, observe it as it tries to light the burner. If the igniter glows for more than 90 seconds or doesnt glow at all its too weak or has malfunctioned. In either case, the igniter needs to be replaced.

    Also Check: Counter Top Oven With Air Fryer

    More articles

    Latest article